Gene assembler

Gene assembler

A workbench for creating implantable xenogerms from genepacks stored in nearby gene banks. Genepacks are not consumed in this process and can be reused.

Base Stats

Type

Building – Biotech (Buildings)

Market Value

550  ^[Note]

Beauty

0

HP

500

Flammability

50%

Path Cost

42 (24%)

Building

Size

2 × 3

Minifiable

False

Placeable

True

"PassThroughOnly" is not in the list (impassable, pass through only, standable) of allowed values for the "Passability" property.

Passability

PassThroughOnly

Cover Effectiveness

0%

Terrain Affordance

Light

Power

-100 W

Creation

Required Research

Xenogenetics

Skill Required

Construction 4

Work To Make

12,000 ticks (3.33 mins)

Resources to make

200 + 4

Deconstruct yield

100 + 2

Destroy yield

50 + 1

The gene assembler assembles one or more xenogenes into an implantable xenogerm.

Acquisition

Gene assemblers can be constructed once the Xenogenetics research project has been completed. They require  200 Steel,  4 Components, 12,000 ticks (3.33 mins) of work, and a Construction skill of 4.

Summary

For a general guide to the gene system, see Genetics.

The gene assembler's interface.

The gene assembler must be connected to nearby gene banks, which must contain genepacks. The gene assembler can access the genes in these stored genepacks, and reassemble them into an implantable xenogerm.

Using the gene assembler, you can combine your genepacks for your own desired custom xenotype. Any type and number of gene can be added, as long as no genes conflict, and as long as you do not exceed the maximum genetic complexity, or the minimum metabolic efficiency.

Genetic Complexity

By default, the assembler's maximum genetic complexity is 6. The maximum complexity is raised by 2 for each gene processor that is currently connected and active. Up to 100 processors can be connected, for a hard maximum of 206 complexity.

Gene processors will only contribute complexity when powered. If the connected processors lose power during recombination, and the maximum complexity falls below the xenogerm's requirement, then recombination will be put on hold.

Genetic complexity affects the time required for the Gene assembler to combine your genes. For a gene assembler with one gene processor attached, a xenogerm of complexity 1-2 takes an estimated 4 hours to assemble, complexity 3-4 takes 5 hours, complexity 5 takes 6 hours, complexity 6 takes 7 hours, complexity 7 takes 8 hours, and complexity 8 takes 9 hours. These times are reduced by increasing Research Speed, but increased as the xenogerm becomes more complex.

Metabolic Efficiency

Nearly all non-cosmetic genes will affect your pawn's metabolic efficiency, which in turn affects their hunger rate. A higher metabolic efficiency represents a pawn that uses less energy, and requires less food. Likewise, a lower metabolic efficiency represents a hungrier pawn that requires more food. There is a tradeoff, where positive genes result in lower efficiency, and negative genes result in a higher efficiency (with a few exceptions).

A valid gene combination requires a metabolic efficiency of -5 or higher, resulting in a maximum of 225% hunger rate. Positive, efficiency-lowering genes must be balanced out by negative, efficiency-raising genes for the xenogerm to become valid. Any number of efficiency-raising genes can be applied, but the effect will only stack up to +5 efficiency, at a minimum of 50% hunger rate. Any more metabolic efficiency beyond this point will have no effect.

Archite Capsules

It is also possible to include any number of archite genes into your xenogerm. However, each archite gene requires some number of archite capsules, which must be loaded into the assembler to begin recombination.

---

Once you are done customizing your xenotype, a researcher will begin processing the xenogerm. The process takes a few hours, or even days, depending on the xenogenes selected and the worker combining them. When finished, a completed xenogerm will be dropped onto the ground nearby. This process does not require any resources, apart from archite capsules if necessary.

Linking

Gene assemblers can link to gene banks and gene processors up to 11 tiles from the building edge in a circular radius. Linking requires line of sight to the gene assembler building, so processors and assemblers should be placed in the same room to be considered connected.

Version history

• Biotech DLC Release - Added
• 1.4.3534 - Fix: Pawns will continue to create a xenogerm until they pass out.
• 1.4.3541 - Empty genepacks no longer display in the gene assembler dialog.

---

Architect

Biotech

Band node • Growth vat • Mech booster • Mechband antenna • Mechband dish • Mech gestator • Large mech gestator • Mech recharger • Large mech recharger • Pollution pump • Subcore encoder • Subcore softscanner • Subcore ripscanner • Wastepack atomizer

Deathrest

Deathrest casket • Deathrest accelerator • Hemogen amplifier • Hemopump • Glucosoid pump • Psychofluid pump

Genetics

Gene assembler • Gene bank • Gene extractor • Gene processor